Loading
Hello, folks. This is my first post here. I'm having trouble getting my geothermal system started on generator power. Below are some of the...
Started by Jaredg in Generac Air Cooled Generators
I just finished the installation of my 20KW with whole house transfer switch. During the installation though I accidentally broke off one of the Male...
Started by tjcin in Generac Air Cooled Generators
Posted here a few years ago about relocating our 4390 generator and appreciate all the guidance I received. The 4390 is still running well and I've...
Started by ButchNH in Generac Automatic Transfer Switches
I'm looking for input from anyone who knows the 410 c.c. engines. I have a 58700 in the field that burns oil real bad, I have a 4389-3 that runs...
Started by 78buckshot in Generac Air Cooled Generators
From the label on the generator: Item # 0043903 Serial 4076560 This is a 15/13kw generator fed with natural gas, installed by me in 2006. Last...
Started by Goofy4TheWorld in Generac Air Cooled Generators
I have a 6K Ecogen, Model 58181 Lp gen as a back up gen to a solar off grid system. Upon arriving at camp this past weekend we discovered the system...
Started by 10kray in Generac Air Cooled Generators
Customer has a 30kw diesel with Evolution 2 controller that will be used to run a water pump manually that is in a remote location that has no AC...
Started by Jacob375r in Generac Liquid Cooled Generators
Hello forum and thank you for providing such a helpful resource. I have a 7kw generac standby generator purchased in 2011, model 58370, serial...
Started by fiddlehead in Generac Air Cooled Generators
I replaced the ignition coil this spring on my 11kva nat gas generator. I was getting a under voltage error code. I adjusted the valves, replaced...
Started by 3Phase in Generac Air Cooled Generators
Just installed a new 22kw unit, 70432, with a whole house transfer switch. The other day we had a power outage for about 5 hours. Everything worked...
Started by traverse517 in Generac Air Cooled Generators
Hi all, I’ve had two SMM modules go bad over the past two months. Both on 30amp fuses, the entire panel protected by a surge protector. What could...
Started by Daveh85 in Installation Talk
I have a new OA9064 rotor and OH8924 stator. Purchased for a vintage 04079-0 (10KW) generator. The rotor is too large to fit into the stator...
Started by PR10Kp in Generac Generator Classifieds
Hello, I have a 5501 8 KW running on propane, 180 hours on clock. Found a RPM sensor loss code, Cleared code manual crank, started up, but sounded...
Started by cic317 in Generac Air Cooled Generators
I contacted PowerMate customer service with the above request, apparently PowerMate is part of Generac now. Got the following response from...
Started by Jim Z in Generac Air Cooled Generators
I bought and installed this unit over a dozen years ago, and it worked very reliability for years, till a major storm came thru and ripped up trees...
Started by nfw01 in Generac Automatic Transfer Switches
Hello guys, I have a 1997 Generac 15KW generator. It has the Fiat 1.6L engine that runs @ 1800 RPM. I am in desperate need a of a fan pulley...
Started by mikroland in Generac Liquid Cooled Generators
Having 2 issues with this generator. Have an H100 panel, First issue, I believe is a bad keypad as I am unable to scroll through any screens or...
Started by Toader13 in Generac Liquid Cooled Generators
am getting 9.45 DC volts it's not getting the full 12dcv can to send the signal to the transferswitch can anyone tell me what's the cause
Started by durell johnson in Generac Air Cooled Generators
In have a 13KW NG 5242, circa 2008 (installed 2009). Has been a good reliable unit ever since the original install, save for the steel enclosure...
Started by kdirk in Generac Air Cooled Generators
Recently, my 2012 10kW generator requires frequent (every 10-15 hours) valve adjustments because of bad starts. This is the exhaust valve in the back...
Started by NorthGuy in Generac Air Cooled Generators
is it possible to eliminate the computer and convert the motor to mechanical Governor.
Started by Kervyn in General
I am confused. Generac still lists a 20kW model as item 7038, but everything I see on Ziller says "new model available". Looking at...
Started by Goofy4TheWorld in Post up what you need, and we will track down the part number for you
SORRY I'M LATE !!!!
Started by BillM in Offtopic Chat
Thanks for having this forum. I have a Liquid Cooled Generac Centurion 40kw with 3.9L that has served us well but after spending over $700 in the...
Started by Greg in Generac Liquid Cooled Generators
Last year there was some talk of Generac coming out with a Wifi monitoring module for the older generators. Is there any word of when this will be...
Started by malba2366 in Generac Air Cooled Generators
Supported videos include:
Please paste your code into the box below: