Posted here a few years ago about relocating our 4390 generator and appreciate all the guidance I received. The 4390 is still running well and I've...
I bought and installed this unit over a dozen years ago, and it worked very reliability for years, till a major storm came thru and ripped up trees...
Hello, I have an older Generac generator and transfer switch with separate electrical panel. The panel was crazy overcrowded and unsafe, so I...
What is the difference between : Generac RXSC200A3 200 Amp Automatic Transfer Switch and Generac RXSW200A3 200 Amp Service Rated Automatic Transfer...
I have a 58710 (10kw air-cooled guardian from a few years ago) that I want to use for backup power at a small radio communications site. I could...
hello. I just installed a used 100amp Centurion (Generac) ATS. I found what appears to be 4 insulators. These are about 2 1/2” x 1”...
Sunday one of my customers took a direct hit to the pole transformer right next to where power came to their meter base on a free standing garage...
Kris K Voeks
hello. I have a RTSS200A that came with the slightly used 36kw generator I bought. Planes on wiring for whole house. But this transfer switch has...
was on a service call today where the customer says recently about once a day every breaker in his transfer switch trips, he personally isn’t home...
Guardian 11KW Model 70331 with Model RXSC200A3.
Had short between E1 and E2 wires which shut down the generator and gave a Low voltage code 1901....
Model 0057440 (20kW; 200AMP) ATS P/N: 0G6389B I am a good DIY person, respect electricity, and know the basics of residential electric systems. A...
Does anyone have a diagram and is thermoplastic wire used. Direct to transfer switch rather than through a power management module.
Hi Guys! I have a 2008 17kw Air Cooled Generator SN# 5100686/Model: 0055040 with a RST prewired load center transfer switch SN# 5105281 that came...
I have an older style Generac 12 circuit ATS paired with a 15kw generator. My main panel is recessed mounted in the garage with the entire top of...
Hi guys and thanks to let me join.I had to go check 2 ATS lately.One was a 200 amps and the other one was 100 amps.
Both new stuff installed last...
Disconnected Generac home generator for a friend and reconnected. Now doesn't go into weekly test mode. What do I need to do? Ty
I recently had a new ATS installed, the power went out today and when it came back the coil fried. Do you have any advice? Is this something once we...
Is a Cummings 20 KW generator compatible with a 200 amp SE rated Generac transfer switch? My customer has a 20 KW Generac installed. New controller...
I'm using a 200a service entry switch with load shedding and want to connect a Daikin split system with two compressors and 4 inside units to the AC...
I have been dealing with a very frustrating Generac install. We bought our home about 2 years ago and the previous family left a Generac 11kw outside...
I am trying to connect existing control wire from older Generac ATS(77032). There are six control wire terminals in the ats. Four match the generator...
I recently bough a Generac 100 Amp SE rated ATS RXSW100A3 to go with a used 2016 11KW Generator and am doing a self install. I studied quite a bit...
RTSS Load Shed Automatic Transfer Switch with DIP switch set to auto reconnect after 15 minuets.
While in standby...
Hello. First post, so please forgive me if I am doing this wrong in any way.
I am researching some options for load shedding. I came across these SMM...
The newer EGEN17-01 requires a 120 volt fused line for battery charger which is not available from the EGS200NSEA. This can be supported by buying...
Supported videos include:
Please paste your code into the box below: